Product details
Baja Designs Upfitter Harness for 2024+ Toyota Tacoma
Your Tacoma already has a spot set aside for aux lighting. Toyota left a 5-wire upfitter connector behind the driver-side headlight, tied off with electrical tape. This Baja Designs harness (part 600101) plugs right into it. Once it's in, your Baja lights run off the truck's factory upfitter switches, so you don't need to add an aftermarket toggle switch.
The harness splits the upfitter connector into three separate circuits. That means you can run up to three Baja light setups, each on its own switch. For example, you could put vent lights on one switch, ditch lights on another and grille lights on the third.
Before you order: this harness only works on a Tacoma that has the factory auxiliary switches in the dash. Please check that your truck has them before purchasing. See the fitment notes below.
Highlights
- Plugs into the factory 5-wire upfitter connector with no cutting or splicing
- Three auxiliary circuits: Aux 1 (red), Aux 2 (yellow) and Aux 3 (white)
- Connects to a standard Baja Designs light harness through the harness's switch lead
- Includes three 4-pin red couplers for Baja harnesses that use the red switch connector
- Backed by Baja Designs' limited lifetime warranty against manufacturer defects
Fitment and Factory Aux Switches
Made for the 2024-2026 Toyota Tacoma (4th Gen) with factory auxiliary switches. Which trucks have them depends on the trim and package:
- TRD Pro and Trailhunter: pre-wired factory aux switches come standard in the dash.
- TRD Off-Road: generally included with the Premium package and higher builds, but it can vary by model year and package.
- SR, SR5, TRD PreRunner and TRD Sport: usually not included, though some trucks with premium packages have them.
Not sure what your truck has? Look for the aux switch buttons on your dash, or give us a call at (657) 400-2009 and we'll help you check before you order.
What's in the Box
- (1) 2024-On Toyota Tacoma Upfitter Harness (60-0101)
- (3) 1/8" 4-pin red couplers (20-0111)
You'll also need a Baja Designs light kit with its own harness. This harness connects that kit to your factory switches. It doesn't replace the light harness.
Installation
Plan on about 1 to 2 hours. You'll need a 10mm socket, a sharp blade, a pick and some zip ties.
- Disconnect the negative battery terminal.
- Find the factory upfitter connector behind the driver-side headlight. It's taped back against the harness.
- Plug the upfitter harness into the factory connector.
- Remove the switch lead from your Baja Designs light harness. If it uses the 4-pin red connector, swap in the included red couplers.
- Connect the light harness to Aux 1, 2 or 3, plug in your lights, then reconnect the battery and test.
For the full step-by-step, see the official Baja Designs installation instructions (PDF).
Rather have us do it? We wire Tacoma lighting in our shop all the time. Check out our installation services or call us at (657) 400-2009.
Baja Designs Lighting for Your 2024+ Tacoma
Here are the Baja Designs light kits we carry for the 4th Gen Tacoma. The first two are built around Tiny Rig Co mounts we design and make in-house.
- Billet Vent Light Mounts with Squadron 2.0 lights for the factory bumper vents
- Squadron 2.0 A-Pillar Ditch Light Kit
- S1 Vent Light Kit
- S8/S2 Pro Grille Conversion Light Kit
- S8/S2 Pro Grille Light Kit for the TRD Pro
Shipping
Orders typically ship within 1 week.